Gang Rip Saws For Sale

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

ZHW800-70- SMW Gang Rip Saw - Saw from 3/8"-2 3/4"T x 31 1/2"W, 11"dia Saw Blade, 1-10 Blades, 29hp Motor. Also Available: ZHW800-80- SMW Gang Rip Saw - Saw from 3/8"-3 1/4"T x 31 1/2"W, 12"dia Saw Blade, 1-10 Blades, 40hp Motor. ZHW800-100- SMW Gang Rip Saw - Saw from 3/4"-4"T x 31 1/2"W, 14"dia Saw Blade, 1-10 Blades, 49hp Motor.

SCM M3 Multi-Blade Dip Chain Gang Rip SawSpecifications: -- 300 mm (11.81") Width cap. -- 110 mm (4.33") Max. depth of cut. -- 8-3/4" Throat depth. -- 390 mm (15.35") Min. stock length. -- 200 - 350 mm (7.87" - 13.78") Blade diameter. -- Arbor dia. 70 mm (2.76"). -- Table size 750 x 1,530 x 750 mm H (29-1/2" x 60.24" x 29-1/2" H). -- Blade speed 4,200 RPM. -- Feed speeds 6 - 48 MPM (19 - 157 FPM).Equipped with: -- 44 kW (60 HP) - 3,554 RPM Blade motor. -- Variable speed drive feed chain motor. (2) Upper infeed & (2) Upper outfeed 4" Dia. rollers, Automatic chain lubrication. -- Top & bottom anti-kickback fingers. -- Main dust hood, with 200 mm (7.87") Dia. outlet. -- 40"; x 2-3/4"; H Adjustable infeed fence. -- Motor load meter.Complete with: -- Operation & Maintenance Manual. -- Tooling (As pictured).

SCMI M3 Gang Rip Saw Includes: Misc blades

SCMI Beam Saw was functioning well when taken out 12 years ago, scoring saw, and some blades. Needs to go $3,500. 713-304-8544

SCMI Gang Rip Saw S/N B.540480

SCMI M3 Rip Saw Still under power for inspection

Dip Chain Multi Saw Believed to be a SCMI 2 extra arbors Extra blades

Shurman Double Arbor Gang Saw 12" Capacity Thin Kerf Babbit Grinder

Silver Straight Line Rip Saw 15 HP Motor

It is a 2 saw re-rip with one moveable saw and an adjustable fence. Capacities: Minimum length = 8” Maximum length = 192” Minimum width = 1 ½” Maximum width = 6” Minimum thickness = 7/8” Maximum thickness = 1”

Multirip circular saw for block cutting, with reinforced structure and high production speed. Trailed top and bottom rollers, upper rollers with adjustment, shafts with cartridge system for quicker and more efficient replacement of the set of saws, U-beam base with levelers and central lubrication. It does not come with the circular saws. - Maximum inlet width: 600 mm; - Minimum inlet height: 70 mm; - Maximum inlet height: 160 mm; - Double arbor: Ø 80 mm; - Number of saws per axle: 10x; - Exterior saws Ø: 350 mm interior saws - Ø: 110 mm; - Upper press rollers: 2x; - Bottom rollers: 6x; - Max. Feed speed: 35 m L / min for logs - 160mm above in diameter; - Max. Feed speed: 40-50 m L / min - only for logs 130-160mm in diameter; - Lower main motor indicated: 200 hp 2p (1x) Included; - Top main motor indicated: 150 hp - Main motor belt: 4 / 3v (8 Pcs); - Motor traction of the rollers: 5 cv 4p; - Gearmotor: GS (crown and pinion); - Length: 3366 mm; - Width: 2782 mm; - Height: 2233 mm; - Approximate weight: 5.470 kg

WINTERSTEIGER - DSG 150 ECO, ...Thin Cutting Frame SawSide & Center Guides: Fitted as standard on the basic machine to guarantee the broadest possible range of application. Specifications: -- 11 kW (15 HP) Main motor; 0.3 - 1.5 MPM feed speeds; 210 mm saw frame stroke with (450) strokes/Min. -- 30 - 216 mm Cutting height, adjustable as required; max. +/- 0.5 mm difference in block height. -- 60 - 150 mm Cutting width (side guide); (2) 23 - 70 mm cutting width (using center guide); (2) channels max. 72.5 mm using 7.5 mm guide or with (5) channels max 24.5 mm using variable block width; 300 mm min. block length. -- 1.5 mm Cutting accuracy; +/- 0.2 mm Cutting loss (depending on saw length). -- Max. (30) saw blades (excluding scraper saws); (3) 120 mm sawdust extraction tubes. -- "Air Jet" Module: Cleans the lamellas and saw blades during the sawing process by blowing away the sawdust; cools down the saw blades during the sawing process and cleans the shaving space of the saw blades. -- "Air Jet" also increases the saw blades life and improves the lamella's accuracy. Sawdust-free lamellas can then be glued immediately after cutting.Comes with transformer

Wintersteiger DSG Sonic Frame Saw

RipMaster400 with Auto skewing - Heavy Duty 60 HP Motor Touchscreen controls 2 movable blades Infeed System with Scanning ( We offer 3D rip optimization as well) Custom outfeeds available. 480V 3Phase Seimens Electronics

RipMaster400 with Auto skewing - Heavy Duty 60 HP Motor Touchscreen controls 2 movable blades Infeed System with Scanning ( We offer 3D rip optimization as well) Custom outfeeds available. 480V 3Phase Seimens Electronics