Oakley Edge Sander

Ogden SL3660 RFS

Oliver 36" Band Resaw

Oliver Sawmill New Carriage Wheels New battery

Front/rear trim Top/bottom trim Top/bottom bevel Moulding Edgesanding

Single horizontal drill and dowel; 1300 mm work table with four fields; sure shot revolver system to guarantee the fastest cycle time, average one second, and extreme reliability; simple user friendly touch screen; heavy duty steel frame for maximum rigidity; large phenolic table with robust clamps suitable also for delicate materials; barcoding and ethernet ready; laser for measuring the part and populate the program;

3 Moulding heads 1 grooving head workpiece length 2300 mm workpiece thickness 35 mm Hopper feed Numeric controller

Omnitech Selexx Pal CNC Router

7.5 HP single phase cyclone/dust collection assorted dust pipe and fittings as pictured

The machine has been cleaned, checked and repaired 5HP 230V 3Ph

Onsrud Inverted Router

Optisand L202 Moulding Sander

Optimatic TS-06 Tooth Straightener Manufacturer specs: Every Tooth - Every Run - Every Time Introducing the TS06 automatic bandsaw tooth straightener. This latest Filing Room innovation from OPTIMATIC is designed to work in place of the backfeed on a bandsaw sharpener. The TS06 is timed from the feed of the bandsaw sharpener. Each tooth is examined as it passes through the sensor. When a tooth is not aligned properly it will bend it back to correct it. Teeth are examined on each round of the grinder, giving the tooth straightener the opportunity to examine each tooth several times as the saw is processed and make progressive improvement putting the tooth back in line. A standard 5' resaw can generally be processed in 30 minutes. The TS06 is designed to measure the body of the tooth, just below the grinding burr and just behind the swage or tip. The actual contact point is easily adjustable. It's important to measure the body of the tooth so that we do not cover up problems with swages, shapers, or tippers. - but instead provide them a square, strong tooth to work from. 1. The TS06 has two stations. The first station feeds then measures. 2. The second station bends. Specifications:Connection values:Electrical connetion:220 V 50 Hz or special voltageAir Pressure:1/4? Gas threadAir:Minimum 5 bar air consumption, 1 liter per strokeSaw blade diameter:Saw Wide:From 80 mm to 300 mm wide or special up to 420 mmSaw Long:From 6 m in the grinding machine carousel can be integratedSaw Thickness:0,7 mm to 2,7 mmDimensions:Length:1350 mmHeight:1550 mmWidth:600 mmWorking position:1000 mm can be adapted to grinding heightWeight:210 kg

Optimal 4-Side Canter See photos fro complete specs

7.5 HP 230/460 volt 3 phase 20” blade

9 speed transmission 6 wheel drive 46# rear lockers 23574 miles/24800 hours

This system was purchased new in 2011. It is started up every week for 15 minutes. Ready to be removed. FIRE PUMP 2000 USGPM@ 125 PSI UL/ CONTROLLER GRP-GPU 575/3/60 Note: INCLUDED: FIRE VERTICAL TURBINE FIRE PUMP 2000 USGPM @ 125 PSI , UL/ULC/FM APPROXIMATELY 25' COLUMN ONE TORNATECH 200 HP AUTO TRANSFORMER REDUCED VOLT STARTER C/W AUTO TRANSFER SW MODEL GPR/GPU 575/3/60 NEW WET PIPE SPRINKLER SYSTEM FOR PUMP ROOM C/W CONTROL VALVE & FLOW SWITCH TEST HEADER ONE JOCKEY PUMP SERIES GS MODEL 150H20-8, 100 USGPM@180 PSI ONE HOSE RAACK C/W 50 ' HOSE WALL HYDRANT CONNECTION FOR FIRE DEPARTMENT SEISMIC INSTALLATION DRAWINGS C/W HYDRAULIC CALCULATIONS

Deuma RF/S150 A-V

Turbosaw that was used a few times by seller. This machine did not work well with mesquite trees.

Decorative Curbmaking model 225