CBI 400 Grinder

Cefla Sorbini T/20-3-STP Triple Head Print & UV Line (3) Print Head System (2) IR Ovens Available Immediately

Cefla Rotostain 2000

Cefla Roctre/D Reciprocating 2 Head Spray Machine 1600 mm wide spray area.

Cefla Roctre/D Reciprocating 2 Head Spray Machine 1600 mm wide spray area.

(14) spindles with 1-1/2 hp motors on each. On/off switch for each motor. chucks adjust to grip up to 1/2” bit stroke adjustable from 4” to 10” 121” x 39-1/2” table with (4) hold downs Adjustable speed hydraulic feed 230 volt 3 phase

- Width capacity 53”. Drum, Drum, Combination Head (see sander specs - Head 1: Rubber covered contact roll, 10” dia, 65 shore adjustable with dial - Head 2: Rubber covered contact roll, 10” dia, 65 shore adjustable w/dial - Head 3: Combination head, (2) 5-1/2” finishing drums w/platen - 440 V, 60 cy, 3 Phase - Year 2000, Good Condition - Warehoused after plant shut down factory in 2013 - Have manuals /spec sheets - Machine weighs app 6000#’s. - Buyer must pay for riggers to load onto truck. (our forklifts can’t pick it up)

CEMCO 3 Head Industrial Sander. Running when removed from location.

Nice CF Nielson BP5500 Press. The plant shut down in 2014. The machine was run again for a test in 2016 and everything was in good working condition. They have the dies and pistons to make round and octogonal logs. - Briquetting press CF Nielsen BP5500 - Dies to make 3’’ round logs and 2½’’ octogonal logs - Lignin dosing system - Water pump to add water if material too dry - Home-made automatic speed adjustment with encoder. - Briquette breaker from CF Nielsen at the end of the cooling line - Home-made flying saw with lenght asjustment at the end of the cooling line too with capability to switch from the saw to the breaker. - Can run up to 1200kg (even 1400kg I think) per hour depending on material and briquette shape - Cooling line can be opened to make pucks also. - 575V AC motors - Installed in 2008 - 10,865 hours

CFORM Edger/Rip Saw - model CKM160 This machine was purchased new and installed the beginning of 2023. It has less than 20 hours. The seller changed applications. Machine is ready to load. Photos coming! Manufacturer information: Double Edgeing & Slicing Cutter the value of lumber with clean edges can often exceed the value of rough-cut boards. In one pass, this Twin Blade Board Edger takes boards fresh off the mill and turns them into clean, square edged lumber. This edger is easy to use, with one fixed blade and one moveable blade that adjusts with a manual dial. Easily select the precise size of lumber you need. Lower the perimeter fence when you need to edge only one side of a board. Features: Movable finger iron platers for safe guidance and protection. Maximum 15 raws circular saws, adjustable distances. Hydraulic upper roller pressure and movable cyclinders. Maximum cutting height (inch)6 5/16?, 4 11/16?

This grinder was removed from service in good working condition. It is ready to load/currently in storage 200 HP Main Motor Cutters 117 F-Cutters Screen (4 ) 22" Diameter Wide with 1-1/2" Holes The width is 51” and the height is 17” (infeed opening)

Champion 5 HP 575 Volt 2 Stage 24 CFM unit.

Automatic template Maker for grinding your own Molder knives

Automatic template Maker for grinding your own Molder knives

15 HP 6500 CFM 10” WC

Clark Lift 9' Mast Unsure of model number. Plate is worn down. Machine starts and runs.

Clark 6000 lb 60” forks side shift Hard tire

Cleaver Brooks 200 HP Boiler

Cleaver Brooks Boiler 500 HP 4-Pass dryback Natural Gas 60 PSI Design pressure

Cleereman Carriage PawTawJohn setworks and 3D scanner Three headblock model LPC-42 Four position dogs in/out and bottom dog turning Spare cylinders for all positions Spare top and bottom dogs 30 hp hydraulics