?Cresswood EF-60 Grinder 100 HP 60” Wide Feed Opening Includes 60”W Vibrating Conveyor (shaker table)

2017 Diamond z 4000 horizontal grinder -Approx 7,500 hours and will go up. Used daily -New discharge belt -765hp c18 -Wireless remote -Comes with 1-1/2" Screens, 3"x5" Screens, spare main hydraulic pump and misc parts

Diehl SL50 Straight Line Rip Saw 240 volt 3 phase Variable speed control SN: 51108

Diehl model MR-90 Gang Rip Saw Twelve ( 12 ) inch saw arbor width capacity- Roll feed 50 HP 3600 RPM arbor motor -direct coupled wired 480 volts, 3 phase- new motor bearings 2 HP variable speed feed motor 50 to 150 FPM feed speed-variable Four powered top feed rolls- Excellant feed roll gears 12 inch arbor with one (1) sleeve with spacers Adjustable rip fence Serial number : 66M-1668 Cleaned , checked , and painted

DIEHL 990 GANGRIP SAW Product No. 1001 30 HP - 3600 RPM arbor motor-AB size 4 starter-110 volt controls 12 " arbor width with 3-1/2" maximum thickness 8 roll feed - 4 top (powered) - 4 bottom Anti-kick back fingers : top and bottom One (1) saw cartridge-2 3/4 " saw blade bore New arbor bearings 5 HP feed: single speed Rip fence Outboard bearing on arbor 3" throat capacity to 1st saw blade Cleaned, painted and checked Serial # : 54174 Year: 1958

MLS Number 10682943 DIEHL SL52 STRAIGHT LINE RIP SAW Bottom arbor 4-1/4"X8-1/2" capacity 15 HP 3,545 RPM arbor drive motor Infeed speed up to 200 FPM Serial# 10/88M-5312-4728 Voltage: 460/60/3 phase Amps: 21.7 Wiring diagram # 2-9000-0026 Was removed from service in November 2020

MLS Number 10689968 Globe 5 Head Panel Trim Saw Approximate panel capacity: 8 feet wide X 26ft long Saw was cutting large full size sheets (8ft+ x 26ft) at a particle board manufacturer Lugs on chains have micro adjustment bolt ( brass) Air cylinders raise and drop heads Brands of chain: Woodward & White Overall width: 14 ft. 6inches Overall height: 6 ft. Overall length: 33 ft. 4 inches+-

GO FAST DD79 DEDUSTER High Speed Board Deduster 230V 3Ph

MLS Number 12543674 Hazlethorn Stake Pointer 240V single phase Air operated control Needs new cutters

Keystone Deduster 2013 Details coming soon

54" Horizontal Resaw Wide Blade Excellent Machine 400K Replacement Cost

MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.

2018 Morbark 3400XT Wood Hog Horizontal Grinder CAT C18, 765 Hp engine Approx 2100 hours New belly belt/skirting; Rebuilt mill Engine has new cylinder sleeves with rod & main bearings, purge pump & hydraulic fan motor (replaced by manufacturer due to a defect) Remote Magnet 1” & 5” screens Great machine and ready to go to work

Morbark Chip Blower Hopper Feed Came out Running 10 HP Motor

2022 Morbark 3000XT Horizontal Grinder -180 hours -575 hp CAT engine -Remote -Still under warranty NEW NEW NEW

Murphy Rogers MRM-16-185H Shaker Dust Collector 16” dia. inlet 25 hp exhauster motor 81 filters 6” dia. x 68” lg 668 sq/ft of filter 6,000 cfm estimated capacity Serial Number: 1020

8 Head Drop Saw 40' x 14' 5 Strand lumber Deck (Infeed) 16' x 5' 5 Strand Lumber Deck (Infeed) 16' x 5' High 8 Strand Unscrambler (Infeed) 100' x 24" Scrap Conveyor (Outfeed) Drag Chain Underneath (Outfeed) 24" Roll Case (Outfeed) Electric Disconnects And Controls Optional 4 Strand Roof Top Transfer Optional 82' Of 5 Strand Lumber Dcck

Northtech Machine NT-GRS-300RF Gang Rip Saw REDUCED Roller feed Max depth of cut is 4". Max width is 12". New Saw Blades And Spacers

2006 Peterson 4710B Tracked -6720 chassis hours -Remanufactured engine installed on machine as the old clutch destroyed the engine -Done by CAT dealer in NC (GregoryPoole) -Reman engine 530hrs -New clutch installed the same time as reman engine installed -Feeder floor 30-40% life left -Rotor balance is good -New main conveyor belt just installed -New main conveyor head motor installed -New skirting guard deflectors installed under rotor -New set of screens in machine I think they are 3" -New clutch module and harness -New Iqan electrical panel upgrade system installed by Peterson rep -C18 T3 caterpillar 755HP -Twin disc clutch Ready to work

2003 Peterson HC5400 Grinder -7700 hours -New set of bananas, grates, and teeth -Has a wireless remote -Rotor recently balanced and serviced -New tires ands wheel bearings on axle -Comes with 25K worth of parts MACHINE RUNS AND WORKS BUT NEEDS A FEW MINOR REPAIRS -Has a hole in the metal plate that covers the rotor -Has a small leak in the fuel tank we currently use an auxiliary tank -Intermittent issue of conveyor not feeding. Believe it is a broken wire