Barr Mullin Wondersaw Optimizer with Computerized Laser Controls Tichniess: Up to 3" Width: 31" Min cut: 4" Feed height: 34-1/2" Floor Space: Apprx 21' x 15' 480 volt

10 HP 3200 rpm main motor 2.7 HP feed motor Cuts on crayon marking Variable feed up to 262 fpm 18” blade 30 mm arbor 460 volt 3-phase (2) Roller conveyors can be included if needed

Cornell Double Arbor Gang Saw

This unit has been in storage for some time and will need some TLC.

The seller has upgraded to a new machine and no longer needs this rip saw. This machine still runs a few times a week at the shop. 15 HP Motor 2 HP Feed Motor 2" Arbor 16" Max blade capacity Chain drive

Diehl Model 75 Straight Line Rip Saw Chain is in good shape. Left and right chains are worn evenly. Includes: Laser Variable Speed: 4-speeds

Griggio C250 Rip Saw 250 mm Wide belt (10")

Rip Saw Model SDL 1200 Edging Conveyor Model UHY 1900

This system was purchased used and never put into service.

Madison 202 Straight Line Rip Saw

Mattison 404 Rip Saw Seller was using until they upgraded to a gang rip. Ready to ship.

The Rip Saw is still in good running condition and still in use.

Mereen Johnson Model 312 Rip Saw Includes: New pads for the chain Includes: Twistlock Collar Mounted Saw Blades Available approx May 1, 2024

Mereen Johnson 424DC 24" Wide Arbor 75 HP Motor (460v/3Ph) 3 HP Feed Speed Variable Feed Speed Air loaded pressure rollers

Mereen Johnson 424 DC Gang Rip Outfeed Rollers

Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm

Mereen Johnson 424 Gang Rip Saw

Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....

Mereen Johnson 431 DC